Our Blurred frosted window film is a stylish self-adhesive film ideal for glass partitions or glass in commercial buildings. Available by the metre in 1.5m width.Read More
Our Blurred frosted window film comes on a 1.52m wide roll making it ideal for glass partitions and for large windows in commercial buildings.
The film is graded, starting from clear to frost, and back to clear again, giving some privacy in the area in the center of the film.
This film comes with a clear release liner, as opposed to our trademark paper liner available on most of our products. This makes it more difficult to mark when cutting small pieces. We cannot cut this film to size, only to length.
The film is suitable for any smooth glass surface including double glazed units, and can be used anywhere in the house or office, including bathrooms and kitchens as it is resistant to condensation.
Very easy, and very quick. But don't take our word for it - read our fantastic Trustpilot reviews, they're all genuine.
To apply the film, all you'll need are a few basic tools, and we even throw in a small application tool with your order for free. Soapy water is the key ingredient, which allows you a bubble free application.
Should you require to have the film installed professionally, please contact us with some details of your project.
|Performances||Blurred Partition Window Film|
|Scratch resistant coating||YES|
|Clear Single Pane||YES|
|Tinted Single Pane||YES|
|Clear Double Pane (non toughened)||YES|
|Clear Double Pane (toughened glass)||YES|
|Clear Laminated single pane||YES|
|Clear Laminated Double Pane||YES|
|Tinted Double Pane (non toughened)||YES|
|Tinted Double Pane (toughened glass)||NO|
|Low-E Double Pane||YES|
Regardless of the type of window film or stickers you purchase, whether frosted, tinted, mirror or decorative, the principle on how to fit window film will be the same. We also have several targeted video tutorials which you will find by clicking here.
Make a slip solution using a few drops of washing up liquid mixed with water in a spray bottle and thoroughly clean the glass. Use a glass scraper to remove specks of paint, or any other glass covering like stickers.
Unless your window film is already cut to size, and if the film has a paper liner with a metric grid, measure your glass at the top and bottom, and left and right and mark and cut your window film. You can also cut the film bigger than required and trim it once applied to the glass.
A. Throughroughly wet the glass with the slip solution.
B. Place the window film face down an a flat surface and expose a small amount of the adhesive or cling side.
C. Spray the adhesive or cling side liberally with the slip solution as you peel off the protective liner.
D. Slip the adhesive or cling side of the film on the glass butting one edge and the top against the window frame or rubber gasket (double glazed unit).
A. Liberally wet the face of the film with the solution to act as a lubricant fro your squeegee or felt edged tool.
B-C. Squeeze out the solution from under the film using a firm and even pressure, starting from the top and working your way down and across the film.
Run a credit card and a retractable knife blade down the edge of the glass to trim any excess film. The thickness of the card will allow for a small gap to help any remaining solution to be squeezed out. Once trimming is complete go over the film once more to squeeze out all the solution.
1. Make sure that all the solution has been squeezed out.
2. Wipe the film and any remaining solution with paper towel.
3. Inspect the film on both sides of the glass to check for any trapped solution or air bubbles.
Removing window film can be a very easy process, but it all depends on how long the film has been on the glass, and the type of film that was used.
Here's a video tutorial which shows the basic principal.
Typically, films are either made using PVC or PET.
PVC is a soft material which can be peeled off the glass with a glass scraper. Any glue residue can be removed with soapy water and a scraper.
PET is a brittle material widely used for solar and safety film, and might be made of layers of mettalised material. To remove this type of film, use a wide glass scraper and lubricate with soapy water to remove the film.
As a rule, old PET film are more difficult to remove than PVC films.
For large panes, it is best to first score the film into strips with a sharp knife. This means that you can tackle it in more manageable pieces.
Window film is very easy to look after and you won't need any special products to clean it with. In fact, soapy water, similar to the solution you used to apply the film is the best cleaning product.
Wait for at least 3 weeks before first cleaning your film
Use soapy water
Use a soft cloth or paper towel
Use a rubber edged squeegee (unless the film is printed or has cut outs) in good condition
Do not use abrasive products
Do not use Amonia based products
Do not use defective or damaged squeegees
Extra care must be taken when cleaning printed films, or films which have been cut out and have exposed edges. Gently clean with a soft cloth only, and take particular care around the cut areas. Do not rub too hard or use a squeegee as it could damage the print or your cut film.
Take extra care around the edges and clean your sticker or film from the centre out. Do not use a squeegee.