Purlfrost | Window Film For Home Or Business | Retail Glass StickersCreated with Sketch.

Dark Static Cling Reflective Film

Our static cling reflective one way mirror film is ideal for reducing excess glare and heat, and thanks to it's mirror like finish, it cand also act as a daytime privacy film. This film is non adhesive so can easily be applied, removed, stored and re-used at a later stage.

Read More
Width
Length

Width
cm
  • Please Select Width
Height
cm
  • Please Select Height
  • Please Select Quantity
15% off - when you buy 2 films or more cut to the same measurements. The discount will be applied HERE, not at checkout.
  • You must confirm the measurements before continuing.
£0.00

Free UK shipping when you spend £100.00

Measurement Convertor

0 cm

Product Description

  • Reduces UV light by 82% 
  • Reduces glare by 83%
  • Rejects solar energy by 79%
  • Visible light transmission 24% *
Static cling reflective window film (also referred to as mirror privacy film) is a tinted film with a mirror finish when viewed extrenally. It is designed to ward off the sun's glare and heat and to keep your home, office or conservatory cooler. It also helps with reducing UV light by 99%, and major cause of fading in furnishings. This is the ideal product if you need a temporary and reusable room darkening film.
 
Can it be used for privacy?
The reflective quality of the film will also offer varying levels of privacy, when used on exterior facing windows. 
The privacy effect will only work during day time hours, on windows exposed to sunlight, so this film might not be suitable for North facing or shaded windows.
 
Where is the film most effective?
As a rule, we recommend  the darker films for south facing windows, where the sun is harsher. East facing windows will be exposed in the morning, when the sun is low, and west facing windows in the afternoon when the sun is high, but brighter. For east and west facing, we recommend both the dark and the medium films, depending on how exposed your windows are to the sun.
North facing windows shouldn't be too affected by the sun.
 
IMPORTANT NOTE:
If you are planning to install this film on a double glazed unit, make sure the glass is toughened. If it is, it will have a kite mark in one of the corners of the pane. If you apply this film on glass that is not toughened, the glass could crack due to poor build quality especially on older units. If in doubt, you could consider the Medium static reflective film alternative.

How to order
You can order the film by the meter, or for ease of installation, cut to size. Unlike frosted window film which comes with a paper liner, this film comes with a clear polyester protective liner which has no metric grid printed on it. You'll therefore need a large flat surface, a straight edge and a retractable knife to cut the film to size, or have a quick look at our video tutorial which shows a quick and easy way to cut large pieces of film.

How to apply
The film is applied to the glass using a soapy water solution. Please click here to view our video tutorial, showing how to apply large pieces of film. The process is the same for small pieces of film which you will be able to apply single handedly.

Samples
Not sure whether this is the right film for your purpose? We offer free 10cm x 10cm samples. The pictures depicting the film are only for illustration purposes, so a sample is recommended to make an educated choice. If you'd like to try a larger piece before committing to a large order, just order a small amount of film, or a cut to size piece to test on a pane.

Returns and refunds
We will only accept returns for films purchased by the metre. Just send it back to us in it's original condition and packaging. We cannot accept returns for films cut to size however, as they have no resale value.

* Visible light transmission
In most offices where the lights tend to be on all day, the loss of natural light is not a big issue. In a home environment, the loss of daylight might be more of an issue, and we would recommend this film on large windows, or in a room with several windows. 


Back to top

Product Specification

Download
Performances Dark Static Cling Reflective Film
U V Transmission Help Icon 18%
Visible light reflection Help Icon 60%
Visible light transmission Help Icon 24%
Total solar energy rejected (Heat) Help Icon 79%
Solar reflection Help Icon 55%
Solar absorption Help Icon 33%
Solar transmission Help Icon 12%
Glare reduction Help Icon 83%
"g" value(Solar heat gain coef.) Help Icon 0.2
"u" value(EN673W/m2.k0) Help Icon 5.1
Emissivity Help Icon 0.22
Scratch resistant coating Help Icon NO
Compatibility Help Icon
Clear Single Pane Help Icon YES
Tinted Single Pane Help Icon YES
Reflective Tinted Single Pane Help Icon YES
Clear Double Pane (non toughened) Help Icon NO
Clear Double Pane (toughened glass) Help Icon YES
Clear Laminated single pane Help Icon NO
Clear Laminated Double Pane Help Icon NO
Tinted Double Pane (non toughened) Help Icon NO
Tinted Double Pane (toughened glass) Help Icon YES
Low-E Double Pane Help Icon NO
Gas Filled Double Pane Help Icon NO
Triple Pane Help Icon NO
Polycarbonate roof Help Icon NO
Domed skylights Help Icon NO
Application
Internal Help Icon YES
External Help Icon NO
Warranty
Internal warranty(Years) Help Icon 5
External warranty(Years) Help Icon N/A
Against Peeling Help Icon NO
Against Cracking Help Icon NO
Against Demetallization Help Icon NO

How To Apply

Step by step instructions on how to apply window film & frost glass

Regardless of the type of window film or stickers you purchase, whether frosted, tinted, mirror or decorative, the principle on how to fit window film will be the same. We also have several targeted video tutorials which you will find by clicking here

Glass Preparation (the crucial task)

Glass Preparation

Make a slip solution using a few drops of washing up liquid mixed with water in a spray bottle and thoroughly clean the glass. Use a glass scraper to remove specks of paint, or any other glass covering like stickers.

Film Cutting

Film Cutting

Unless your window film is already cut to size, and if the film has a paper liner with a metric grid, measure your glass at the top and bottom, and left and right and mark and cut your window film. You can also cut the film bigger than required and trim it once applied to the glass.

Film Application

Film Application

A. Thoroughly wet the glass with the slip solution.

B. Place the window film face down an a flat surface and expose a small amount of the adhesive or cling side.

C.  Spray the adhesive or cling side liberally with the slip solution as you peel off the protective liner.

D. Slip the adhesive or cling side of the film on the glass butting one edge and the top against the window frame or rubber gasket (double glazed unit).

 

Squeegee Technique

Squeegee Technique

A. Liberally wet the face of the film with the solution to act as a lubricant fro your squeegee or felt edged tool.

B-C. Squeeze out the solution from under the film using a firm and even pressure, starting from the top and working your way down and across the film.

Film Trimming

Film Trimming

Run a credit card and a retractable knife blade down the edge of the glass to trim any excess film. The thickness of the card will allow for a small gap to help any remaining solution to be squeezed out. Once trimming is complete go over the film once more to squeeze out all the solution. 

Final Checks

1. Make sure that all the solution has been squeezed out.

2. Wipe the film and any remaining solution with paper towel.

3. Inspect the film on both sides of the glass to check for any trapped solution or air bubbles.

How To Remove Window Film

Removing window film can be a very easy process, but it all depends on how long the film has been on the glass, and the type of film that was used.

Here's a video tutorial which shows the basic principal.

Typically, films are either made using PVC or PET.

PVC is  a soft material which can be peeled off the glass with a glass scraper. Any glue residue can be removed with soapy water and a scraper.

PET is a brittle material widely used for solar and safety film, and might be made of layers of mettalised material. To remove this type of film, use a wide glass scraper and lubricate with soapy water to remove the film.

As a rule, old PET film are more difficult to remove than PVC films.

For large panes, it is best to first score the film into strips with a sharp knife. This means that you can tackle it in more manageable pieces.

 

Measuring Tips

Ready to place your window film order?

You will first need to measure the glass, in centimetres, using a tape measure. Only measure the glass you want to cover.

Width: measure from left to right at the top and the bottom of the glass, and take note of the largest measurements (some older wooden windows are not perfectly square).
Height: measure from top to bottom on the left and the right of the glass, and take note of the largest measurements.

Top tip

Leaving a clear gap around frosted or patterned film is a stylish and practical option, allowing you to peep out when someone is at the door for example. To create a clear outline around the film, deduct twice the width of the desired clear outline, to the width and the height of your pane. 


For example, if you want a 1cm (10mm) clear gap all the way round, deduct 2cm from the width, and the same from the height.
Fitting the film with a gap all the way round is much easier, especially on old wooden windows and doors which are not always in the best condition, and where the edge of the glass has paint encroachment.
 

Care

How To Care For Your window film After Installation

Window film is very easy to look after and you won't need any special products to clean it with. In fact, soapy water, similar to the solution you used to apply the film is the best cleaning product. 

Do's

Wait for at least 3 weeks before first cleaning your film

Use soapy water

Use a soft cloth or paper towel

Use a rubber edged squeegee (unless the film is printed or has cut outs) in good condition

Don'ts

Do not use abrasive products

Do not use Amonia based products

Do not use defective or damaged squeegees

Caring for printed films, or films with cut-outs

Extra care must be taken when cleaning printed films, or films which have been cut out and have exposed edges. Gently clean with a soft cloth only, and take particular care around the cut areas. Do not rub too hard or use a squeegee as it could damage the print or your cut film.

Caring for static cling films & stickers

Take extra care around the edges and clean your sticker or film from the centre out. Do not use a squeegee.