Purlfrost | Window Film For Home Or Business | Retail Glass StickersCreated with Sketch.

Anti Fade Window Film NUVF 60

Our anti fade window film NUVF 60 is a lightly tinted metalized film designed to reduce excess ultraviolet (UV), visible and infrared (IR) light, all of which are causes of fading to home furnishings, woodn floors, paintings and photographs. This fade protection window film reduces ultraviolet light by 99.5%. The film can be purchased by the metre in a length and width of your choice, or for ease of installation cut to size.

NOTE: No window film can completely prevent fading. For best results, choose a film that also targets visible light and infra red light. As a rule, the darker the film, the more efficient it is at mitigating fading.

Read More
Width
Length

Width
cm
  • Please Select Width
Height
cm
  • Please Select Height
  • Please Select Quantity
15% off - when you buy 2 films or more cut to the same measurements. The discount will be applied HERE, not at checkout.
  • You must confirm the measurements before continuing.
£0.00

Free UK shipping when you spend £100.00

Measurement Convertor

0 cm

Product Description

  • Reduces UV light by 99.5%
  • Reduces visible light by 66%
  • Reduces infra red light by 42%
  • Safeguard furnishings, wooden floors, artwork and photographs
  • Order by the metre

Our anti fading window film is the most efficient at reducing all 3 main causes of fading in furnishings.

All printed and coloured furnishings in our homes and offices, including photographs and paintings, as well as timber flooring and carpets, will eventually fade due to the sunlight, ambient air and pollution. By applying UV blocking window film on all glazed areas, you will greatly extend the lifespan of your precious items.

Our anti fade window film is the market leading product of its kind due to having a different composition to most. Typically, anti fade films are made using only one layer of polyester yet ours has two with UV treatment on both layers therefore providing double protection from harmful rays.

There are six factors affecting fabric fading:

  • Ultraviolet Light is the main cause of fading

  • Visible Light

  • Infrared light

  • Humidity

  • Chemical Vapours (including ozone)

  • Age of Fabric

  • Dye Fastness

There is no window film that can completely eliminate fading however it can offer maximum protection from fading caused by solar ultraviolet light and solar heat.

Our film is widely used by heritage bodies, museums, art galleries and private buyers. We’ve even had the pleasure of providing Buckingham Palace with our second-to-none anti fade film!


Back to top

Product Specification

Download
Performances Anti Fade Window Film NUVF 60
U V Transmission Help Icon 0.5%
Visible light reflection Help Icon 11%
Visible light transmission Help Icon 66%
Total solar energy rejected (Heat) Help Icon 42%
Solar reflection Help Icon 18%
Solar absorption Help Icon 26%
Solar transmission Help Icon 56%
Glare reduction Help Icon 28%
"g" value(Solar heat gain coef.) Help Icon 0.59
"u" value(EN673W/m2.k0) Help Icon 5.8
Scratch resistant coating Help Icon YES
Compatibility Help Icon
Clear Single Pane Help Icon YES
Tinted Single Pane Help Icon YES
Clear Double Pane (non toughened) Help Icon YES
Clear Double Pane (toughened glass) Help Icon YES
Clear Laminated single pane Help Icon YES
Clear Laminated Double Pane Help Icon YES
Tinted Double Pane (non toughened) Help Icon YES
Tinted Double Pane (toughened glass) Help Icon YES
Low-E Double Pane Help Icon YES
Polycarbonate roof Help Icon NO
Domed skylights Help Icon NO
Application
Internal Help Icon YES
External Help Icon NO
Warranty
Internal warranty(Years) Help Icon 10
External warranty(Years) Help Icon N/A
Against Peeling Help Icon YES
Against Cracking Help Icon YES
Against Demetallization Help Icon YES

How To Apply

Step by step instructions on how to apply window film & frost glass

Regardless of the type of window film or stickers you purchase, whether frosted, tinted, mirror or decorative, the principle on how to fit window film will be the same. We also have several targeted video tutorials which you will find by clicking here

Glass Preparation (the crucial task)

Glass Preparation

Make a slip solution using a few drops of washing up liquid mixed with water in a spray bottle and thoroughly clean the glass. Use a glass scraper to remove specks of paint, or any other glass covering like stickers.

Film Cutting

Film Cutting

Unless your window film is already cut to size, and if the film has a paper liner with a metric grid, measure your glass at the top and bottom, and left and right and mark and cut your window film. You can also cut the film bigger than required and trim it once applied to the glass.

Film Application

Film Application

A. Thoroughly wet the glass with the slip solution.

B. Place the window film face down an a flat surface and expose a small amount of the adhesive or cling side.

C.  Spray the adhesive or cling side liberally with the slip solution as you peel off the protective liner.

D. Slip the adhesive or cling side of the film on the glass butting one edge and the top against the window frame or rubber gasket (double glazed unit).

 

Squeegee Technique

Squeegee Technique

A. Liberally wet the face of the film with the solution to act as a lubricant fro your squeegee or felt edged tool.

B-C. Squeeze out the solution from under the film using a firm and even pressure, starting from the top and working your way down and across the film.

Film Trimming

Film Trimming

Run a credit card and a retractable knife blade down the edge of the glass to trim any excess film. The thickness of the card will allow for a small gap to help any remaining solution to be squeezed out. Once trimming is complete go over the film once more to squeeze out all the solution. 

Final Checks

1. Make sure that all the solution has been squeezed out.

2. Wipe the film and any remaining solution with paper towel.

3. Inspect the film on both sides of the glass to check for any trapped solution or air bubbles.

How To Remove Window Film

Removing window film can be a very easy process, but it all depends on how long the film has been on the glass, and the type of film that was used.

Here's a video tutorial which shows the basic principal.

Typically, films are either made using PVC or PET.

PVC is  a soft material which can be peeled off the glass with a glass scraper. Any glue residue can be removed with soapy water and a scraper.

PET is a brittle material widely used for solar and safety film, and might be made of layers of mettalised material. To remove this type of film, use a wide glass scraper and lubricate with soapy water to remove the film.

As a rule, old PET film are more difficult to remove than PVC films.

For large panes, it is best to first score the film into strips with a sharp knife. This means that you can tackle it in more manageable pieces.

 

Measuring Tips

Ready to place your window film order?

You will first need to measure the glass, in centimetres, using a tape measure. Only measure the glass you want to cover.

Width: measure from left to right at the top and the bottom of the glass, and take note of the largest measurements (some older wooden windows are not perfectly square).
Height: measure from top to bottom on the left and the right of the glass, and take note of the largest measurements.

Top tip

Leaving a clear gap around frosted or patterned film is a stylish and practical option, allowing you to peep out when someone is at the door for example. To create a clear outline around the film, deduct twice the width of the desired clear outline, to the width and the height of your pane. 


For example, if you want a 1cm (10mm) clear gap all the way round, deduct 2cm from the width, and the same from the height.
Fitting the film with a gap all the way round is much easier, especially on old wooden windows and doors which are not always in the best condition, and where the edge of the glass has paint encroachment.
 

Care

How To Care For Your window film After Installation

Window film is very easy to look after and you won't need any special products to clean it with. In fact, soapy water, similar to the solution you used to apply the film is the best cleaning product. 

Do's

Wait for at least 3 weeks before first cleaning your film

Use soapy water

Use a soft cloth or paper towel

Use a rubber edged squeegee (unless the film is printed or has cut outs) in good condition

Don'ts

Do not use abrasive products

Do not use Amonia based products

Do not use defective or damaged squeegees

Caring for printed films, or films with cut-outs

Extra care must be taken when cleaning printed films, or films which have been cut out and have exposed edges. Gently clean with a soft cloth only, and take particular care around the cut areas. Do not rub too hard or use a squeegee as it could damage the print or your cut film.

Caring for static cling films & stickers

Take extra care around the edges and clean your sticker or film from the centre out. Do not use a squeegee.