Purlfrost | Window Film For Home Or Business | Retail Glass StickersCreated with Sketch.

Emerald D

This Art Deco stained glass effect film is based on an actual period stained glass design. To order, just enter the size of your glass pane(s) and our designers will resize the design to suit. The resulting film is very easy to apply in minutes.

Read More
Width
cm
Height
cm
15% off if you buy 2 or more of the same product at the same size.

I confirm that the measurements I entered are in centimetres and correct for width and height.
  • You need to confirm measurements.

Step by step instructions on how to apply window film & frost glass

Regardless of the type of window film or stickers you purchase, the principle will be the same. We also have several targeted video tutorials which you will find by clicking here

Glass Preparation (the crucial task)

Glass preparation before applying window film.

Make a slip solution using a few drops of washing up liquid mixed with water in a spray bottle and toughroughly clean the glass. Use a glass scraper to remove specks of paint.

Film Cutting

Unless your film is already cut to size, and if the film has a paper liner with a metric grid, measure your glass at the top and bottom, and left and right and mark and cut your film. You can also cut the film bigger than required and trim the film once applied to the glass.

Film Application

A. Throughroughly wet the glass with the slip solution.

B. Place the film face down an a flat surface and expose a small amount of the adhesive or cling side.

C.  Spray the adhesive or cling side liberally with the slip solution as you peel off the protective liner.

D. Slip the adhesive or cling side of the film on the glass butting one edge and the top against the window frame or rubber gasket (double glazed unit).

 

Squeegee Technique

A. Liberally wet the face of the film with the solution to act as a lubricant fro your squeegee or felt edged tool.

B-C. Squeeze out the solution from under the film using a firm and even pressure, starting from the top and working your way down and accross the film.

Film Trimming

Run a credit card and a retractable knife blade down the edge of the glass to trim any excess film. The thickness of the card will allow for a small gap to help any remaining solution to be squeezed out. Once trimming is complete go over the film once more to squeeze out all the solution. 

Final Checks

1. Make sure that all the solution has been squeezed out.

2. Wipe the film and any remaining solution with paper towel.

3. Inspect the film on both sides of the glass to check for any trapped solution or air bubbles.

How To Remove Window Film

Removing window film can be a very easy process, but it all depends on how long the film has been on the glass, and the type of film that was used.

Here's a video tutorial which shows the basic principal.

Typically, films are either made using PVC or PET.

PVC is  a soft material which can be peeled off the glass with a glass scraper. Any glue residue can be removed with soapy water and a scraper.

PET is a brittle material widely used for solar and safety film, and might be made of layers of mettalised material. To remove this type of film, use a wide glass scraper and lubricate with soapy water to remove the film.

As a rule, old PET film are more difficult to remove than PVC films.

For large panes, it is best to first score the film into strips with a sharp knife. This means that you can tackle it in more manageable pieces.

 

How To Care For Your window film After Installation

Window film is very easy to look after and you won't need any special products to clean it with. In fact, soapy water, similar to the solution you used to apply the film is the best cleaning product. 

Do's

Wait for at least 3 weeks before first cleaning your film

Use soapy water

Use a soft cloth or paper towel

Use a rubber edged squeegee (unless the film is printed or has cut outs) in good condition

Don'ts

Do not use abrasive products

Do not use Amonia based products

Do not use defective or damaged squeegees

Caring for printed films, or films with cut-outs

Extra care must be taken when cleaning printed films, or films which have been cut out and have exposed edges. Gently clean with a soft cloth only, and take particular care around the cut areas. Do not rub too hard or use a squeegee as it could damage the print or your cut film.

Caring for static cling films & stickers

Take extra care around the edges and clean your sticker or film from the centre out. Do not use a squeegee.

£0.00

Free UK shipping when you spend £50.00

Measurement Convertor

0 cm

Product Description

This stained glass effect film design can be ordered printed on a non frosted film for added colour vibrancy, or on frosted film for added privacy. The non frosted film will still allow for some privacy so would be ideal for a front door, but we wouldn't recommend its use in a bathroom where privacy is more of an issue, and where the frosted film option would be more suitable.

To order, just supply your measurements in centimetres for accuracy.
For example, 300mm equals 30cm, 355mm equals 35.5cm, 1 metre equals 100cm, 1m55 equals 155cm.
For accurate measuring, take a measurement at the top and bottom, as well as the left and right side of the glass. If there is any discrepancy, use the largest figures for both height and width. You can trim the excess film to suit after installation.

For any film you order of the same design and measurements, you get a 15% discount. If 2 panes are slightly different in size and to still benefit from the discount, use the highest and widest measurements. You can always trim the excess material after installation.

Please refer to our video tutorial for installation tips.


Back to top