Purlfrost | Window Film For Home Or Business | Retail Glass StickersCreated with Sketch.

Beaumont Stair Sticker A

Our Victorian inspired stair stickers are easy to apply and long lasting, thanks to a thin laminate designed to protect the printed colour. You can order this particular design in a colour of your choice, or you can order it in a selection of colours for added effect. You can also mix and match the colours and the designs to create a trully bespoke look.

Read More
Width
cm
Height
cm
  • Print Colours
  • Dull Gold
  • White
  • Grey
  • Yellow
  • Dark Yellow
  • Light Orange
  • Orange
  • Red
  • Burgundy
  • Magenta
  • Fuschia
  • Purple
  • Turquoise
  • Teal
  • Cyan
  • Dark Green
  • Indigo
  • Light Green
  • Mint
  • Latte
  • Olive
  • Brown
  • Charcoal
  • Pink
15% off if you buy 2 or more of the same product at the same size.

I confirm that the measurements I entered are in centimetres and correct for width and height.
  • You need to confirm measurements.

Step by step instructions on how to apply window film & frost glass

Regardless of the type of window film or stickers you purchase, the principle will be the same. We also have several targeted video tutorials which you will find by clicking here

Glass Preparation (the crucial task)

Glass preparation before applying window film.

Make a slip solution using a few drops of washing up liquid mixed with water in a spray bottle and toughroughly clean the glass. Use a glass scraper to remove specks of paint.

Film Cutting

Unless your film is already cut to size, and if the film has a paper liner with a metric grid, measure your glass at the top and bottom, and left and right and mark and cut your film. You can also cut the film bigger than required and trim the film once applied to the glass.

Film Application

A. Throughroughly wet the glass with the slip solution.

B. Place the film face down an a flat surface and expose a small amount of the adhesive or cling side.

C.  Spray the adhesive or cling side liberally with the slip solution as you peel off the protective liner.

D. Slip the adhesive or cling side of the film on the glass butting one edge and the top against the window frame or rubber gasket (double glazed unit).

 

Squeegee Technique

A. Liberally wet the face of the film with the solution to act as a lubricant fro your squeegee or felt edged tool.

B-C. Squeeze out the solution from under the film using a firm and even pressure, starting from the top and working your way down and accross the film.

Film Trimming

Run a credit card and a retractable knife blade down the edge of the glass to trim any excess film. The thickness of the card will allow for a small gap to help any remaining solution to be squeezed out. Once trimming is complete go over the film once more to squeeze out all the solution. 

Final Checks

1. Make sure that all the solution has been squeezed out.

2. Wipe the film and any remaining solution with paper towel.

3. Inspect the film on both sides of the glass to check for any trapped solution or air bubbles.

How To Remove Window Film

Removing window film can be a very easy process, but it all depends on how long the film has been on the glass, and the type of film that was used.

Here's a video tutorial which shows the basic principal.

Typically, films are either made using PVC or PET.

PVC is  a soft material which can be peeled off the glass with a glass scraper. Any glue residue can be removed with soapy water and a scraper.

PET is a brittle material widely used for solar and safety film, and might be made of layers of mettalised material. To remove this type of film, use a wide glass scraper and lubricate with soapy water to remove the film.

As a rule, old PET film are more difficult to remove than PVC films.

For large panes, it is best to first score the film into strips with a sharp knife. This means that you can tackle it in more manageable pieces.

 

How To Care For Your window film After Installation

Window film is very easy to look after and you won't need any special products to clean it with. In fact, soapy water, similar to the solution you used to apply the film is the best cleaning product. 

Do's

Wait for at least 3 weeks before first cleaning your film

Use soapy water

Use a soft cloth or paper towel

Use a rubber edged squeegee (unless the film is printed or has cut outs) in good condition

Don'ts

Do not use abrasive products

Do not use Amonia based products

Do not use defective or damaged squeegees

Caring for printed films, or films with cut-outs

Extra care must be taken when cleaning printed films, or films which have been cut out and have exposed edges. Gently clean with a soft cloth only, and take particular care around the cut areas. Do not rub too hard or use a squeegee as it could damage the print or your cut film.

Caring for static cling films & stickers

Take extra care around the edges and clean your sticker or film from the centre out. Do not use a squeegee.

£0.00

Free UK shipping when you spend £50.00

Measurement Convertor

0 cm

Product Description

What a wonderful addition to your home and a huge saving on the cost of real tiles.
Printed on a Self Adhesive, Durable, Wipeable material, these stickers are very easy to apply as they will be made to measure, exactly to the size you have ordered.

How to order
Please enter your measurements in centimetres, but to the nearest millimetre for accuracy: (eg 22.6cm H x 67.2cm W - don't forget that decimal point!). Most of your panels should be the same size, but do check that they are. Your bottom riser may be wider than the ones above, or may have a curved edge. The upper stairs will be varying in size if they turn onto a landing, so be sure to measure carefully and order the right amount!

Colours
You can order all your stickers in one colour, or mix and match the colours for a trully stunning effect. You can only order one colour at a time so just add to basket after each colour selection.
Please note you will get a 15% discount automatically when you place an order for 2 or more of the same colour and size.

Preparation
Make sure the surface you are planning to stick the stickers to is smooth, clean and dry.

Please note that these stickers are only designed to go on the riser (vertical part of the stair) as they will not be durable enough to withstand the traffic on your treads!


Back to top